您好!欢迎来到济南锌力特门业有限公司 !

产品中心| 在线留言| 联系我们

济南道闸,济南停车场管理系统,济南电动门厂家,济南岗亭厂家济南锌力特门业有限公司专业生产电动门、直线门、岗亭、道闸、停车场管理系统、旗杆、护栏等

全国咨询热线
  • 13705316729
  • 0531-83169966
    济南道闸起落杆出现故障怎么办?
    文章来源:www.jnxltmy.com   作者:锌力特门业   时间:2017-06-29

      济南道闸起落杆出现故障怎么办?

      What happens to the landing gear of Ji'nan road brake?

      1、 断电保护开关断电:当道闸的控制部分失灵时,道闸的自动保护装置将自动工作,此时闸杆停在斜上位置不动,总电源断开,机器不工作。此时将机器门打开,将大皮带顺时针方向旋转3-8圈到上位时即可复原。若如此多次不能恢复原状,则需检查霍尔元件和电路板是否失灵。

      1, power-off protection switch: control part of the power brake failure, automatic protection device gate will automatically work, the brake lever to stop position does not move on the ramp, the total power is disconnected, the machine does not work. At this time, the door will be opened, the large belt clockwise rotation, 3-8 laps to the upper can be restored. If so many times can not be restored, you need to check whether the Holzer components and circuit boards are out of order.

      2、道闸的活节螺丝松动:活节螺丝为正反螺纹相接,上下两个轴承之间用双头螺杆相接,若螺丝松动,将造成上下位均不准确。用一个80MM长Ф4的铁棒插入双头螺杆之间旋动调整闸杆上下到位即可。

      2, road brake live screws loose: live joint screws for positive and negative thread connection, the upper and lower two bearings with double headed screw connection, if the screw loose, will cause the upper and lower is not accurate. With a length of 80MM with diameter of 4 bar into the double screw rotating between the brake lever on the place can be adjusted.

      3、道闸的拐臂螺丝松动:若此螺丝松动,将造成道闸的闸杆上下位不准确和停杆时晃动较大,将螺栓悬紧,螺母锁紧即可。

      3, the gate of the crank arm screw loose: if the screws are loose, will cause the brake bar gate the inaccuracies and stop when a large rock, the bolt hanging tight, tighten the nut.

      4、下拉钩调整螺母松动:机箱内下部设有螺纹M10的下拉钩,其功能为拉住平衡机构的弹簧和平衡功能的零点调节。

      4, the drop hook adjustment nut is loose: the lower part of the case is equipped with a screw M10 pull down hook, and its function is to pull the balance mechanism of the spring and balance function of zero adjustment.

      5、 到位控制磁铁挪位:上下到位均采用慈敏霍尔元件,若长方形磁铁与减速机带凸轮的圆片位置改变,造成到位不准确。将其调整准确,不可翻转,即可解决问题。

      5, place control magnet move position: upper and lower positions are adopted Tzu sensitive Holzer components, if the rectangular magnet and reducer with cam disk position change, resulting in inaccurate. Adjust it accurately, and can not flip, you can solve the problem.

      6、道闸的线圈埋线松动:当地感线圈不能牢固的固定在巢内时,汽车压过路面的震动会造成巢内线圈变形,改变地感初始电感量,此时传感器必须重新复位后方能正常工作。解决方法是将融化的沥青浇入内使其固定。

      6, gate coil catgut embedding loose: local sense coil can not be firmly fixed in the nest, the car off the road vibrations will cause the deformation of the coil inside the nest, sense of change in the initial inductance, the sensor must be reset back to work properly. The solution is to pour the melted asphalt into it and secure it.

    同类文章:
    收缩
    • 电话咨询

    • 13705316729