您好!欢迎来到济南锌力特门业有限公司 !

产品中心| 在线留言| 联系我们

济南道闸,济南停车场管理系统,济南电动门厂家,济南岗亭厂家济南锌力特门业有限公司专业生产电动门、直线门、岗亭、道闸、停车场管理系统、旗杆、护栏等

全国咨询热线
  • 13705316729
  • 0531-83169966
    电动伸缩门安装需要注意哪些事项?
    文章来源:www.jnxltmy.com   作者:锌力特门业   时间:2017-06-22

      下面由济南电动门厂家多年来安装经验与大家分享,如何安装无轨的伸缩门,当然也可以用于有轨的安装方法,主要是无轨伸缩门普遍性比有轨伸缩门要好,所以在这里介绍无轨的安装方法。

      Below by Ji'nan electric door factory installed over the years experience to share with you, how to install the trackless telescopic door, of course, can also be used for rail installation method, mainly trackless telescopic door universal than rail telescopic door is better, so the installation method of the trolley here.

      一、伸缩门安装步骤

      I. installation steps of telescopic doors

      1.固定门体:将门体放入轨道,尾部的底撑用专用固定卡及地脚膨胀螺钉(M12×80)固定。

      1. fixing door body: the door body is put into the track, and the bottom support of the tail is fixed with a special fixing card and a ground expansion screw (M12 * 80).

      2.限位开关:按照设定门体的开、关位置埋设限位装置。

      2. limit switch: according to setting the door body opening and closing position embedment limit device.

      3.固定控制盒:控制盒可以装在机头箱内,也可移至离主机10米之内的室内。

      3. fixed control box: control box can be installed in the head of the box, can also be moved to within 10 meters from the host room.

      4.连接线路:严格按接线图依次接好相对应的连线(严禁在通电状态下接线),接线要牢固,端子与端子之间不能短路,并捡查线路是否正确。

      4. connection circuit: in strict accordance with the wiring diagram in turn to meet the corresponding line (strictly prohibited in the state of power wiring), wiring to be firm, between terminals and terminals can not short-circuit, and check whether the line is correct.

      二、伸缩门安装调试

      Two 、 installation and debugging of retractable door

      1.首先用手动的方式人工推拉门体,检查门体运行是否正常,在确定门体运行正常的情况下,方可接通电源。

      1., manually push the sliding door body first, check whether the door is running properly, and make sure that the door is running properly, you can turn on the power supply.

      2.接通电源,控制盒电源指示灯亮,按“开”按纽,“开”指示灯亮,门体能自动打开至设定的限位处自动停止。按“关”按纽 ,“关”指示灯亮,门体能自动关闭至设定的限位处自动停止。

      2. connect the power control box, power indicator light, click "open" button, "open" indicator lights, door can open automatically to set the limit at the automatic stop. According to the "off" button, "off" indicator lights, door can automatically close to set the limit at the automatic stop.

      3.在调试运行过程如发现门体运行限位不准确,可调整限位开关的高度。

      3. in the debugging operation process, if the door running limit is not accurate, the height of the limit switch can be adjusted.

      4.调试运行5次以上,如一切正常方可投入使用。

      4., debugging run more than 5 times, such as all normal before they can be put into use.

    同类文章:
    收缩
    • 电话咨询

    • 13705316729